DESCRIPTION
This powerful synchronous switching step-up/step-down regulator efficiently produces 5 V from input voltages between 2.8 V and 22 V. Its ability to convert both higher and lower input voltages makes it useful for applications where the power supply voltage can vary greatly, as with batteries that start above but discharge below 5 V. The board measures 0.9″ × 0.9″, has a typical efficiency of 85% to 95%, and can supply typical continuous output currents between 2 A and 4 A depending on the input voltage. The regulator also features reverse voltage protection and an optional enable input that can be used to put the regulator in a low-power state with a current draw of less than 10 µA per volt on VIN.
The S13V30F5 switching regulator (also called a switched-mode power supply (SMPS) or DC-to-DC converter) uses a buck-boost topology to convert both higher and lower input voltages to a regulated 5 V output. It takes input voltages from 2.8 V to 22 V and increases or decreases them as necessary, offering a typical efficiency of over 85% and a typical output current of 3 A. The flexibility in input voltage is especially well-suited for battery-powered applications in which the battery voltage begins above 5 V and drops below as the battery discharges. Without the typical restriction on the battery voltage staying above the required voltage throughout its life, new battery packs and form factors can be considered.
The regulator has input reverse voltage protection up to 20 V, under-voltage lockout, output over-voltage protection, and over-current protection. A thermal shutdown feature also helps prevent damage from overheating and a soft-start feature limits the inrush current and gradually ramps the output voltage on startup.
FEATURES
- Input voltage: 2.8V to 22V
- Typical maximum continuous output current: 2 A to 4 A, depending on input voltage
- Typical efficiency of 85% to 95%, depending on input voltage and load
- 10 mA to 20 mA typical no-load quiescent current (can be reduced to 2 µA to 10 µA per volt on VIN by disabling the board)
- Input under-voltage lockout and output over-voltage protection
- Soft-start feature limits inrush current and gradually ramps output voltage
- Integrated reverse-voltage protection up to 20 V, over-current protection, and over-temperature shutoff
- Fixed switching frequency of ~500 kHz
- Compact size: 0.9″ × 0.9″ × 0.38″ (22.9 mm × 22.9 mm × 9.7 mm)
- Two 0.086″ mounting holes for #2 or M2 screws
RESOURCES
The step-up/step-down regulator has four connections: enable (EN), the input voltage (VIN), ground (GND), and the output voltage (VOUT). The input voltage, VIN, powers the regulator. Voltages between 2.8 V and 22 V can be applied to VIN. VOUT is the regulated output voltage.
The regulator, which is enabled by default, can be put into a low-power sleep state by bringing the EN pin low. The rising threshold for the EN pin is between 1 V and 1.2 V, and the falling threshold is at most 160 mV lower than that (i.e. the falling hysteresis is 160 mV max). This allows a precise low-VIN cutoff to be set, such as with the output of an external voltage divider powered by VIN, which can be useful for battery powered applications where draining the battery below a particular voltage threshold could permanently damage it. The quiescent current draw in sleep mode is dominated by the current in the 475 kΩ pull-up resistor from ENABLE to VIN and in the reverse-voltage protection circuit, which altogether will be between 2 µA and 10 µA per volt on VIN.
The regulator has two sets of through-holes: five smaller holes arranged with a 0.1″ spacing along the edge of the board (for compatibility with standard solderless breadboards and perfboards and connectors that use a 0.1″ grid) and four larger holes intended for 3.5 mm-pitch terminal blocks. VIN, GND, and VOUT are available at both the smaller holes and larger holes, but EN is only available on the smaller row of through-holes.
- Dimension diagram of the 5V Step-Up/Step-Down Voltage Regulator S13V30F5
- 3D model of the 5V Step-Up/Step-Down Voltage Regulator S13V30F5
- Drill guide for the 5V Step-Up/Step-Down Voltage Regulator S13V30F5
Speedy Delivery and Professional Packaging
Due to our longstanding partnership with UPS FedEx DHL, and other leading international carriers, we are able to offer a variety shipping options. Our warehouse personnel will pack all goods to our exacting requirements. Before shipping, your goods will be carefully inspected and secured. We ship to thousands clients every day in a variety of countries. The fact that we're determined to become the largest online retailer in the world is evident. Both Europe and the USA have warehouses and distribution centres.
Note: Orders with more than one item will be assigned a distinct processing time dependent on the particular item.
We will thoroughly inspect all items ordered before shipping. The majority of orders are shipped within 48-hours. Expected delivery time is between 3 and 7 days.
Returns
We do not control the inventory in our warehouse and factory. The actual stock levels can fluctuate at any time. It's possible that you may not receive your order once it has been placed.
Our policy is valid for 30 days. If you don't receive the product within 30 days, we are not able to provide the option of a refund or exchange.
Your item should be in the original packaging and be unused. It must also be returned in the original packaging.
Related products
Component
1.14 inch LCD Display Module for Raspberry Pi Pico – 65K Colors – 240×135 – SPI Seeed Studios
